How to bind the Exceed 2.4G RC Transmitter w/ Fail Safe Tips. RC Helicopters | Radio Control Scale Models, RC Helicopters For Sale | Buy Remote Control Helicopter

TOP BEST RC Helicopters

Online social commentary (media commentary):

Bobby lectures on how to bind your 2.4G Exceed RC radio system w/ some fail safe tips. Buy a high quality and affordable 2.4G RC Radio System at http://www.nitrorcx.com/2piracosy.html

Oh man , I nearly had a incident with my nitro today, had a short circuit on my steering servo and all control of the car on full throttle , thanks for the fail safe!!
"hey Bobby..thanks for help.Question: I don't need to use a binding cable/plug for doing this ? Or is it just that kind of transmitter? Some videos are using those binding cable that plugs to the transmitter..i'm confused a little bit..
."
Question here, you;ve mentioned that when the RX looses signal with TX, the servo position goes back to neutral. Previous your video said, when the car is at the neutral position, make sure that the brake is not engaged, does this mean that there are no certain way to slow/stop the car while it's travelling at extreme high speed?
Hey Bobby! When I switch on the receiver power, the throttle servo slowly judders (vibrates) into full throttle and stays at full throttle and keeps juddering. The throttle servo also doesn't have any control. The steering servo works perfectly and has full control. I have checked all the batteries, they are fully charged. Any advice? Many thanks!
Thanks mate. This also workd on my Kyosho KT201/KR200 system. I couldnt find that bloody fail safe set button. Now I know that its on the receiver and not on my remote control. :D Yeah... I am a noob! Thanks again for sharing!
Hey Bobby, I just got a 1/5th Giant Scale Exceed RC Barca from Nitro RCX, and I was hoping you can lead me to how to install the fail safe cable that comes with the buggy. Thanks in advance for any help you can provide.
"will you damage the fail safe device if you by mistake plug it directly to the batt?

Thanks"
thank you so much for some reason this happend to me when i barley got my rc drift out from the box i thought it broke i=but i guess cuz of ur help it worked thank you so much
Thank you so much! Picked up two new RC cars in a trade today they were both not responing this fixed one.
hey i have a exceed hyperspeed just like the one your using do they come with a built in failsafe ?
can you use the Exceed 2.4G RC Transmitter with other recivers?
THX Man it worked. Your the only one with good advise thanks man
If the light doesn't stay on that could mean that the battery your using as a receiver pack is low.
Hi there. I just placed my order for the barca green w/o the failsafe for $520 and the failsafe 1 is $680. The failsafe the ofna mini fail safe I've found is $17.88. Why the $160 difference? Does it need a new transmitter for failsafe??
"Anyone know if the Dragon-RC receiver that comes with RTR units for the Serpent lineup have built in failsafes?
Also highly recommended for those with nitro RCs to have throttle return springs fitted to the carb in the event of a throttle linkage breakage/disconnect or electronics' power loss. Don't rely on only failsafes as they won't return your throttle to closed position with no power to servos."
how fast does the 1/10 2.4Ghz Exceed RC Electric SunFire RTR Off Road Buggy go?
What flysky radios does the exceed 4ch receiver work with.
So helpful..
How do you reset a receiver to bind to a new transmitter?
Hey my cars steering and breaking twitches when it's in full position. what could be the problem?
What does it mean if my receiver LED is going solid but when I try anything with the remote, nothing happens? Is there a way to check if something is wrong with the servos?
to bobby,ive watched alot of ur videos on you tube & ur a very brainy gent & you now a hell of a lot about rc cars.thank you andy
Do you know if i can bind a 3 channel Controller with a 2 channel reciever?
"Hi is that how you bind any transmitter?
I have a ftx outback 2-in-1 waterproof receiver and esc unit to transmitter"
@101quadrider not waterproof and they are pretty good , the 1/8th scale mad series are better
thanks bobby for the shared...! great share..! NitroRCX is one of my fav channel for getting RC information
is this the same steps for a 27mgh transmitter and receiver? my 27mgh receiver doesn't have a pin to be poked with
Thank you Sooooooooooooooooo much i could not find thing on how to do this Finally
There could be a couple things that might be the issue, the servo might be going bad, or the throttle channel is going bad or the transmitter.
is it normal that it beeps 3 times each time I turn the car on?
So the transmitter is randomly always in bind mode???
What radio system do you have? Have you read the owners manual on how to do the binding procedure?
i have a buggy like that ,but im having a hard time turning it on
the battery is fullly charged, but the red led stays off, and the servos dont make any sound as they usually do, and the transmitter also has 8 aa batteries fully charged
I have a Madcode RC Car. Does any one know how to bind a receiver to the one it comes with?
The factory changed the wiring for the transmitter to only require 4 batteries. It doesn't affect the life span of the batteries.
Have you guys tried putting in some fresh batteries and see if it helps?
when i turn the remote on the full and low lights start to flash and the receiver says bound but i have no control over it, the car just goes directly into fail safe mode
Do you have any control over the RC at all? Do you have steering control? The light on the receiver is suppose to be solid when it's bound to the transmitter.
what receiver brand are you using in the video with that transmitter.. my exceed 4ch receiver's steering channel is not working, only the throttle channel is.. I've tried everything, even touching up very carefully the solder points on the pcb in case one solder joint was defective.. nothing.. throttle works, steering doesn't..